Maytag Moisture Sensor Test - Appliance Repair Forum - Free …
2012年2月8日 · The Maytag doc is 8563816 rev b. The last step of trouble shooting tells you to measure across pins 1 and 2 of the P2 connector. If the resistance is less than 1 Mohm replace the board.
Maytag dryer timer won't advance during cycle - Appliance Repair …
2024年3月10日 · Open control panel and unplug sensor from electronic control board (dryness display). Sensor is the blue wire. If timer still won't advance, unplug connector from control board, check for dirty contacts on control board and plug. Re-seat plug and try again with sensor wire still disconnected. If timer still won't advance, replace control board.
Maytag Dryer Automatic Setting - Keeps Running - Appliance …
2011年11月16日 · Maytag Dryer MDG2500BWW shuts down on Timing Setting, but it keeps running on the Automatic Setting--and does not shut off. I changed the Timer today (Part 330016320) --and the same result: shuts down on regular Timing Setting--but still no change on Automatic Setting as it keeps running.
maytag auto dry not working - Appliance Repair Forum - Free …
2011年8月18日 · Replacement parts for MAYTAG MDE9206AYW DRYER- ELE | AppliancePartsPros.com Here is the service manual Download 1998 Maytag.pdf As you can see from the wiring diagram (Page 9-1) the unit does not have a moisture/dryness sensor. In timed dry the timer motor gets power directly through timer contacts 1 and 2.
maytag neptune dryer will not heat - Appliance Repair Forum
2011年2月11日 · The way it works is that a low voltage is applied to the metal strips, When the clothes are wet the moisture provides a current path between the strips so there is a small current. The control board monitors this and does not advance the …
DG 612 Moisture Sensor Location? And how to replace?
2015年2月23日 · The dryer just runs forever and the clothes get really hot. I believe this means the moisture sensor is bad or needs to be cleaned, but I cannot locate where this is on my dryer. I was told it is in the drum, but I have looked carefully and it is nowhere inside the dryer drum.
Wires To Maytag Neptune Moisture Sensor - Appliance Repair …
2011年12月2日 · When I was replacing the support rollers in my dryer yesterday, the blue wire to the moisture came disconnected. There are several points where I can reconnect it (2 on the opposite end of the ground, one on the same end as the ground).
maytag dryer timer does not advance - Appliance Repair Forum
2010年7月29日 · My dryer is 8 years old. It was running trouble free until lightning struck my house directly; right above the laundry room. It stopped working completely except for the light inside the dryer. I had to replace the dryer cord, terminal block, one of the thermal fuses, and the door switch. I got it in working condition.
Maytag Atlantis Taking 3 Cycles to Dry - Appliance Repair Forum
2013年12月6日 · Parts for Maytag MDE8600AYW Dryer - AppliancePartsPros.com Disconnect the dryness sensor wire at the board. Then using a high resistance scale measure from it to the frame. Be sure to find a bare metal spot. If it is a 3 wire hookup you can measure to Neutral. It should measure a very high if not infinite resistance.
Maytag Epic Dryer stops mid cycle on auto - Appliance Repair …
2013年12月11日 · One time with wet towels it was running for nearly 10 minutes and "sensing." So i opened the door, took a wet towel and rubbed it against the sensor bars, closed the door, started the dryer again, and within about 10 seconds the dryer turned off with the "cycle complete" light on. If I run it on timed dry it completes the cycle without issue.