8.5 Rear end - S-10 Forum
2020年2月19日 · That's a $100 Blazer rear axle. Not a $5-800 8.6". Actually it's pretty clean. Might be worth $125. All S10 8.5's have a reduction in the axle tube size just outside the center section and they all have the big tits on the bottom of the differential housing.
Rear End Options - S-10 Forum
2014年3月26日 · The 7.5 has more of a squared of shape to the cover and straight axles tubes that measure 2 3/4" 8.5 uses a round cover and the axle tubes step down from 3" to 2 3/4" right after they exit the pumpkin. 2wd width from WMS to WMS is 54.5" 4wd width from WMS to WMS is 59" Zr2 width from WMS to WMS is 63" S10 Rear end Ring Gear and Axle Sizes:
Best rear end option for a v8 swap - S-10 Forum
2008年1月14日 · 8.8 is bigger than 8.5 and actually share some 12 bolt dif bearings. 8.8 = 8.8 ring gear 12 bolt = 8.875 ring gear 8.5 = 8.5 ring gear The bigger the ring gear the more contact pattern the stronger the rear. Also the 8.8 31 spline axles …
7.5 or 8.5 10 bolt rear end? - S-10 Forum
2008年3月15日 · Look at post 8 above the lugs on the bottom of the case are very obvious on the corners of the 8.5 whereas the ones are the 7.5 are very small. And as rhot said the axle tubes on a 7,5 are the same diameter all the way across. On an S10 the 8.5 tubes decrease in diameter 3" from both sides of the differential housing. Again it is very obvious.
98 and newer 8.5 s10 rear - S-10 Forum
2018年12月10日 · All of the '68 to '79 X body (Nova and clones), first gen Camaro and '64 to '67 Chevelles had 60 inch rear ends, but only the '72 to '79 X body had the 8.5 rear end (with 28 spline axles). The '60s trucks had the 12 bolt that was about 60 inches wide and 30 spline axles.
S10 7.5 to 8.5 rear end swap - S-10 Forum
2014年11月29日 · S10 7.5 to 8.5 rear end swap Jump to Latest 44K views 9 replies 8 participants last post by Rhotpursuit May 22, 2021
Explorer 8.8 install with pics - S-10 Forum
2013年3月23日 · The Chevy 10 bolt rear end from my 1989 S-15 4X4 Jimmy is a 7.6" with an open diff. Note that 2-wheel drive rear ends are narrower than 4X4 rear ends. If you swapped this 8.8 rear end into your 2wd, the wheels would stick out further. If installing an 8.8 in a 4X4, you do not need to narrow the rear end.
rear end for v8 swap - S-10 Forum
2015年12月2日 · The strongest bolt in rear is the 8.5 that came in late 5 speed 4.3 HO Extremes. S10 Warehouse in Florida usually has them for sale on Ebay but they get around a stack for one. An 89 to 85 disc brake assembly from a Blazer would fit your rig nicely. If you do weld the spiders, make sure you get good penetration with the weld... and weld all of ...
Need help locating an 8.5 rear end. - S-10 Forum
2020年2月23日 · You most likely have an 8.5" rear end with a 10 bolt cover. The ratio of the ring and pi ion is 3.42 : 1. The ring and pinion gear size is going to be 7.625 (7 5/8"). You can get a carrier assembly and ring in pinion from gm parts they are still out there. Or a less expensive option is from Yukon gear. Call them and they will set you up.
Complete 8.8 swap with pics - S-10 Forum
2014年3月10日 · Figured I would share my completed 8.8 swap and experience. So after scoring a disc 8.8 rear diff with 3.73 gears out of an exploder for $20, i right away tore the stock rear diff and rear suspension out of my 86 longbox S10. Here is the old trusty 7.5 sitting on the side lines.